Shore Power Update

Introduction This was one of the projects that took me a long time to understand and plan.  There are a lot of variables, and a lot of opinions on how it ought to be done.  There's also ABYC codes providing input, and enough marketing information to make you insane.  Let's begin by examining what I was starting with. The original CS27 shore power system consists of a Hubbell 30A inlet fitting on the starboard cabin side.  This inlet is then wired with 12G household solid core to a standard outlet in the galley.  That outlet fed an automotive 6A trickle charger in the top of the starboard cockpit locker, and then went on to supply current to a few other outlets on the boat.  There are a number of problems with this configuration, each of which I plan to address in this project. Solid core wiring should not be used on a boat.  All wiring should be stranded.  So, all of the AC wires have to go. The inlet should be connected to a main breaker before going anywhere else.  In this case I need a 30A main. The system needs a reverse-polarity warning light. Branch circuits should be protected by fuses.  In this case I will have one circuit for a charger, and a second circuit for A/C outlets.  My design goal is to have the entire boat run on DC, but when at the docks with shore power connected it can be nice to use it for power tools or chargers that may not be tied into the DC system. The boat outlets should be protected by a GFCI outlet.  This means that the first outlet on that circuit needs to be a GFCI unit.  The rest can be standard outlets. The AC system needs a galvanic isolator to be compliant with current standards. At some point in the future I would really like to replace my inlet with a SmartPlug that incorporates a thermal breaker, and uses a more secure and watertight connection.  Unfortunately, what I have works and the budget doesn't put a high priority on that upgrade quite yet.  Maybe in a few years. Uncovering the Inlet The AC inlet is not the least bit convenient to get to in a stock CS27.  You need to remove trim, and the teak plywood panel on the aft cabin wall.  Removing the trim isn't difficult if you are careful and patient.  You will need a firm but small putty knife to start loosening the pieces near each nail hole, and then I switch to a small pry-bar to remove the pieces.  When you get the wood off the back it will look like the photo to the right. You can see the black AC wire coming in from the cabin side, then down toward the outlet.  Unfortunately, just to check the connections you need to do this much dismantling.  I'm hoping this won't need to happen often, but having gone through this much effort I plan to make sure I do it right. Battery Charger At this point my boat has two Interstate Group 27 deep cycle batteries.  That means just about any charger is compatible.  However, I don't want to rule out the possibility of selecting AGM or other types of batteries in the future.  That means my charger needs to support multiple types of batteries. The next criteria is the amperage capacity of the charger.  I have a 30 amp inlet and shore power cord.  That means the sum of the branch circuits cannot exceed 30A.  My plan was to have a string of 15A outlets.  Technically, that leaves 15A for a charger.  In practical use, I don't plan to have AC in use on the boat.  Since it's already there I'm keeping it, but I want 100% DC components.  For that reason I dabbled with the idea of a more powerful charger.  In the end I decided that sticking to a conservative plan would not only save me money, but make for a more reliable design.  I decided my goal would be  15A charger. Finally, I wanted a "mainstream" unit.  I don't want an obscure charger.  I want one that a lot of other people have on their boats.  I want a charger that someone in a small port chandlery has heard of.  Yes I realize there are brands out there that make great products for less money.  I even researched one in particular that had much praise on Sailnet.  But, integrating a lesser known charger into my boat isn't the plan I'm after as a novice to boat electrical systems.  I need to be able to call in a pro if I get in over my head. I spent much time in Sailing web sites looking at what other people had done, and which brands people had problems or high opinions of.  The more I looked, the more I realized that for every person who likes one product, there is another who doesn't like it.  I also think that people tend to post when they have a bad experience much more frequently than when they have a good one.  So, I took my research with a grain of salt.  I ended up selecting ProMariner's 1215i charger. It can charge two battery banks independently, and it supports multiple battery types.  It was also a model that I was finding on eBay every few weeks at a good price.  When I finally received the package I set up a test in the basement with my batteries and some household wire.  It was silent, and charged both batteries quickly.  The previous owner had (significantly) over-filled the battery electrolite, so the first test run involved a lot of clean up.  I used the hygrometer to suck out the extra fluid, and tried again.  This time, it worked perfectly. Installation is fairly simple.  14 AWG 120VAC input enters through the top and attaches with #10 ring terminals.  The two bank outputs are then jumpered on the bottom as I only need to feed the ACR (which then feeds each bank as needed).  Finally, a single positive and negative 14 AWG wire are run from the charger to the ship's main DC positive and negative busses.  No rocket science involved at all. AC Main Panel Panel Selection After reading Don Casey's This Old Boat, I was planning to try to find an outdoor 30A main breaker box to save money.  I thought I could find one with two branch circuits and save a lot of money compared to purchasing a marine panel.  That plan didn't go so well.  All I could find were huge boxes.  The CS27 isn't a small boat, but there really aren't a lot of wide open surfaces to mount things in.  I quickly realized this was a dead end, and the marine units would be the only thing compact enough to fit what little space I had left. The first thing I discovered after digging into the marine panel suppliers is that most of them start with three branch circuits.  Not too many panels have only two positions.  What's the difference between a two position and a three position?  Almost 2 inches.  Doesn't sound like much until you are trying to find a space to squeeze this thing into.  I found two products that I liked.  First was the Blue Sea Sytems 360 Panel.  The second was from BEP Marine.  While I really like Blue Sea products, I ended up selecting BEP marine primarily because it cost a bit less due to me finding one on eBay.  My decision came down to saving money, but the product I ended up with is very nice.  It's quite solidly built, so I'm not in any way disappointed. Panel Location There are a number of choices available in the boat.  There's probably more than this, but here's my (not ordered by preference) short list: Centered atop the companionway stairs between the main DC panel and the main DC battery switch.  This would require relocating the DC volt meter and enlarging the hole as needed.  It also means the AC panel is in a drip-prone location.  Not ideal. Recessed in the aft cabin trim plywood over the galley. Mounted high in the starboard cockpit locker, over the battery charger.  This would require making a surface-mount box to mount the panel on.  I can't cut out a hole in the bulkhead for this purpose as it would expose the back of the panel to the galley shelf. Mounted inside the engine compartment in a custom panel high, directly over the batteries. As much as I don't want to look at this panel, I think the best place for it will be over the galley and recessed into the coaming.  It will not really look good, but it will be accessible and I will be able to see the reverse polarity light as well as access any breakers that need my attention quickly. Galvanic Isolator For safety and protection from corrosion, this device is pretty important.  I won't get into the details because they are covered thoroughly throughout the Internet and the suggested reading list on this site.  After some research, and recommendations from other CS owners, I went with the Yandina Galvanic Isolator .  It's very reasonably priced and trivial to install. It's the large black box in the photograph above.  One wire goes to the shore power inlet while the other feeds the AC ground bus, which in turn connects back to the ship's main ground bus. 120V AC Outlets One of the circuits on my AC Main panel feeds the battery charger, while the other feeds the AC outlets scattered about the boat.  My original wiring was two-wire (no ground), which is bad.  It also was not a stranded wire, which again fails to meet ABYC codes.  So one thing was certain; the wiring had to go.  I almost left the AC outlets out, but I thought that it might be less work to re-wire them than to fill all the voids where the boxes had been mounted.  I'm sure they will come in handy at some point. I'm not crazy about the galvanized boxes mounted around the boat.  They are tough, but they can rust, conduct electricity, and have not even the slightest resistance to water ingress.  Traditional building materials tend to be less than ideal on a boat, and I tend to think these are better suited to homes.  Having said that, the boxes I have right now are not rusted and the boat is 34 years old.  In the interest of minimizing messes and extra work, I believe I will be retaining their service until I start to see rust appearing. The AC Main panel will feed a GFCI in the galley.  That outlet will chain to the outlet in the wet locker (over the ice box), and that outlet will chain to one located in the V-berth.  I'd like to come up with a creative idea to mount one in the head as well, but that's a (very) low priority. The wire is ABYC compliant 14/3 stranded triplex which I obtained from my favorite Internet shop, GenuineDealz.com.  The stuff was is very flexible, and the sheathing is tough.  It's a bit of a pain to strip, but it will last the remainder of this boat's life time.

Comments

DC System Refit

Introduction

The DC system on Ravat is showing its age as well as its multiple layers of previous owner creativity.   All of this leads to something between a fire hazard and entertainment.  I am happy about neither.  The DC system refit has the following primary goals:

1. Add a new main panel with a more appropriate number of breakers.
2. Install appropriate size battery cables, and properly protect them.
3. Replace lamp cord and non-marine wire with tinned and sealed marine cables.
4. Add proper fuses to all devices.
5. Remove all spaghetti and have all cables labeled when done.
6. Have a good quality battery monitor.

To this end I had quite a few decisions to make.

Main Panel

The original CS panel, while visually pleasing, had extremely old wiring and uses spade connectors.  It is also shy of the number of circuits I need to organize the loads on my boat.  This means I need a new panel.  After a lot of deliberation and measuring I decided that I will keep the main DC panel in the companion way.

Yes, the companion way is an inherently wet location, and is not really where electronics ought to be.  One particularly clever alternative is turning the wet locker into an electronics locker.  I like the aesthetics of that location as well as the dryness, however, I think I want to retain that wet locker for life jacket and foul weather gear storage.  Tight as it is, it works in the tiny cabin.

Having made that decision, I now needed to find a main panel which was horizontally oriented and had at least 8 breakers.  My choice was made fairly simple when the horizontal criteria was considered.  In the end I have selected the Blue Sea Systems #8385 8 position panel.  It's almost a perfect fit for the existing space and gives me two additional breakers over the factory panel.

This will give me plenty of space to organize my circuits.  I'll be consolidating quite a bit in the instruments and accessories cisruits using sub-panels which will free up what would otherwise be a lot of breakers.

Battery Monitor

This was a fairly simple decision.  I looked at a bunch of options, but yet again I was convinced by an excellent article on installing a battery monitor from MaineSail's collection.  Ravat will be sporting a Victron Energy dual bank monitor so I can conveniently monitor both my house bank and starting bank.

Component Fusing

While I'm adding a number of additional breakers, I don't have unlimited space.  With that in mind, I know I will need to consolidate components on circuits.  To do this properly, I want to terminate each device in a block with a fuse.  My first stop was Blue Sea Systems again, and my choice is the #5015 ST Fuse Block.  I will be installing one of these for the instruments circuit, and another for the electronics circuit.

Blue Sea makes two functionally similar units.  One uses the glass tube fuses, the other uses the ST automotive fuses.  I like the idea of the bladed automotive fuses, although I'm not sure why.  After some reasearch I was unable to determine any pros or cons beyond personal preference between the two styles.  As a result, I went with the ST block.

The other decision I had to make here was whether or not I would purchase the model which has a ground terminal, or positive only.  At the time I purchased all of the electrical components I had not fully laid out the locations where they would be mounted.  As it's possible I may need to mount these blocks not necessarily in close proximity to the main ground bus, I thought it would be best for organization and intuitiveness if I was able to terminate each device's positive and negative wires in the same location.

Battery Cables

The existing battery cables were spindly little things that would no doubt explode in a fiery ball if allowed to stay on the boat.  I was advised by many people to use at least a 2AWG cable to create the core DC pathways.  While I certainly can't argue with that being a solid plan, I also couldn't quite justify the additional expense and hassle in routing the wires.

I created a comprehensive electrical plan for the boat.  in it I diagrammed each wire's conservative length and amperage.  There was simply no place anywhere on the boat which could require a 2AWG cable even using the 3% voltage drop tables.  So, since I couldn't find a reason to spend the extra money, I went with 4AWG cables.  I believe the highest load comes from my starter motor, and thus far the boat starts up immediately, and with much greater enthusiasm than the old 10AWG wire which used to feed that starter.

My original plan was to have GenuineDealz.com make my cables to length and terminal size.  Their prices for this sort of thing are fantastic and I would be assured a professional installation.  When it came time to put together the schedule for wire lengths and terminals I quickly realized that the documentation additional effort on my part was just not worth it.  There is a significant variety of post sizes on my busses and components, and to make the wires lay properly, I was going to need very specific lengths, not just "safe" rough estimates.

These realizations led me to purchase the FTZ crimper from GenuiineDealz.com.  It's a lifetime tool to be certain.  Built for industrial use, and works like a charm with the FTZ terminal assortment I also purchased.  Having gone through this project now, I would say without hesitation that making my own cables was the right decision.

Automatic Charging Relay (ACR)

In order to properly maintain the batteries, and ACR will be installed to eliminate the need to switch the battery selector to "all".  If a charging voltage is present, it will charge the batteries.

Adding a Cranking Battery

The goal is pretty simple:  Have a dedicated cranking battery to ensure I can always start the engine if I leave a light on all night.  I don't plan on using this battery for anything but starting, so I will be going with the cheaper true starting battery.  I can also go with a slightly smaller battery since it doesn't have to be a group 27 or 8d to do its job. Despite having the option of going smaller (a group 24 would have been plenty!) I went with a dual purpose battery from West Marine.  It was on sale, and the price was too good to ignore.  Yes, I know that a dual purpose does neither job well, but I picked one that has way more cranking amps than needed, so it will do that job as well as needed.  It also has a little more reserve than a dedicated cranking battery if I need to combine it to keep a light on or something.  At some point you just need to get things done and not get hung up on the details and selection process.  I can always change it out down the road. I selected the port cockpit locker for this battery because the battery compartment next to the engine is full of my house bank on the starboard side.  By placing the cranking battery on the opposite side I add a little balance to the boat (although not as much as I'd like - the house bank is VERY heavy). There's no access to the back side of this bulkhead since it's the ice box.  So, my only option was to use lag screws.  I put in four of them, and they are pretty solid.  I'm not too worried about it.  This is a pretty ugly piece of wood, but I had it kicking around, and it will never show.  At some point I'll go back and glass it into the bulkhead, but I want to run with it for a while to make sure the placement and configuration of the tray is something I want to be permanent.  Knowing me, there will be future tweaks.  In the mean time I will probably give a few coats of Epoxy this fall or next spring just to keep it waterproof. And here is the tray installed onto its cleat.  There is just enough room on the upper side (picture left) to route the bilge pump hoses out of the engine compartment and through the underside of this battery tray.  That will somewhat secure them before they make the journey upwards to their loops before going aft to the through- hulls. The first design flaw I discovered is that the footman loops should have been level with the bottom of the battery box, and not mounted up on the fiddle.  It turns out that they work OK despite, but at some point I'll cut out that area and get them where they need to be. The second thing I discovered is that the nylon webbing that comes with the West Marine (and probably many others since this box looks like every brand I've seen) is almost impossible to release.  It took me about 5 minutes with a flat blade screwdriver to get the teeth out of the webbing.  I'm hoping I had it mounted wrong, because that was the kind of fun I don't need to repeat.  I'll probably substitute webbing from a hardware store at some point to improve the functionality. The cables rout through a notch in the locker divider a few inches above the tray.  Getting them through was easy, and very close to the rest of the wiring harness, which is good for minimizing wire lengths and gauges.

Electrical Projects

The electrical system of the boat is the infrastructure which delivers power to the electronic devices throughout.  It is the batteries, the wires, and the magic that allows all the cool toys to light up and beep. Shore Power Update I believe that Ravat's shore power system was pretty standard, although anything but compliant with ABYC codes.  The automotive battery charger was not well suited to marine battery charging, none of the wires were marine grade, and there was no overcurrent protection to be found.   Some changes were in order. DC System Refit The current wiring is a mix of lamp cord, spaghetti, and a complete lack of compliance with modern codes.  It need to go and be replaced with marine grade wire, real crimped connections, proper fuses, bus bars, and a main DC panel with a reasonable number of fuses.  Is that all?  Ouch. Install Dedicated Cranking Battery The original configuration is two group 27 wet cells.  I don't need AGM batteries, but I'd sure like a dedicated starter battery and a dedicated house bank.  This project will add a dedicated start battery in some yet-to-be-determined location.

Instrument Update

My boat came with a depth sounder and a knot log.  I don't really have any problems with the older Standard  Horizon instruments at all, so if the knot log worked, I wouldn't be touching them.  Unfortunately, the speed log is dead.  Call me a stickler, but I really don't like the look of mis-matched instruments, so off I go on another project.

The original transducers are installed with wood fairing blocks that I find to be less than elegant.  The first problem is that the wood blocks weren't very well protected, and are in rough shape.  The second thing I don't like is that there's no reason to have a paddlewheel perpendicular to the waterline.  It can hug the hull just fine, and that eliminates the need for a protrusion from the hull. 

My research has suggested a CS27 "ideal" practice of mounting the knot log paddle wheel under the floor in the V-birth area close to the bulkhead.  The problem with doing so on my boat is that the teak and holley sole is screwed to the floor and the countersunk holes are bunged.  There's no way to get in there for maintenance.  I'm also not sure of the clearance available since the sole under that teak and holly is solid glass.  For now, that location is out.

In the interest of getting the project done, my current preference is to keep the existing through-hull locations.  The depth sounder will get a new fairing block cast in thickened epoxy.  The speed log will simply parallel the hull.  I will install the speed and depth instruments in exactly the same locations they originally occupied.

The choice of devices will be Raymarine ST60+.  They seem to be the best value for the money.  At this point I have removed the old fairing blocks and wiring and obtained the instruments.  I'm waiting for the barrier coat before installing the fairing blocks and through-hulls.

GPS Chart Plotter Update

Update?  Well, sort of.  I have a small and old hand held Magellan GPS which has graced the cockpit seats many times.  Unfortunately, it chews through batteries like mad.  It is also lacking a solid mount, although I suppose I could remedy that problem.  I'd like to have something hard-wired into the boat's electrical system, with a solid mounting on the pedestal to make it convenient for the helmsman.

Although they are very sexy, the new large touch screen units are not what my old boat needs.  They won't fit the pedestal very well.   They are also too high tech.  Yes, I said it.  If I had a more modern boat I'd probably think about one, but it just throws the aesthetics for me.  I'm looking for something small because I don't want it to be a visual anchor.  I'd like it to mount in the ~ 8 inch area between the pedestal support tubes so that it can be viewed just above the binnacle compass.

From a feature perspective I have no worries.  The features I care about have been part of every GPS unit built in the last ten years.  It needs to be able to output NMEA signals so that my VHF's DSC capability is enabled.  I expect to be able to plot a series of waypoints, see my latitude and longitude, and speed over ground.  A nice feature would be the ability to synchronize with a computer, but it's not essential.  My preference is for an internal antenna, but I can work with external if need be.

Considering these requirements it became obvious that I was looking at low-end units, and I immediately found two which stood out:  The $479 Standard Horizon CP180i, and the $449 Garmin GPSMap 431(Pre-loaded with US Inland Lakes - I'm on Lake Ontario).  The next bump up in price brings me to a $699 Garmin 531 which adds screen resolution.  It's hard to justify an extra $100 for screen resolution when my current hand held unit seems to be working fine, but it's worth keeping in the comparison just in case another feature jumps out.

Feature Comparison

	Standard Horizon CP180i	Garmin GPSMap 431	Garmin GPSMap 531	Garmin GPSMap 541
Adv. Price (defender.com)	$479	$449	$599	$699
Dimensions	4.4"H x 7.1"W x 1.7"D	5.0"H x 5.7"W x 2.7"D	5.9"H x 6.4"W x 2.9"D
Antenna	Internal	Internal (ext optional)	Internal (ext optional)	Internal (ext optional)
Screen Resolution	320 x 240	240 x 320	234 x 320
Screen Dimension	5"	4"
Power Consumption	520mA max @ 12v	15W max @ 13.8v	15W max @ 13.8v	15W max @ 13.8v
Waterproof?	???	IPX7	IPX7	IPX7
Cartography	C-MAP by Jeppeson NT+/MAX	Garmin	Garmin	Garmin

Mounting Location

My intent is to mount the GPS on the pedestal immediately behind the binnacle compass.  Since I'm looking down, I anticipate that the compass will not block the screen significantly.  There are a number of options for raising the mount point a bit to mitigate this situation as well.  When reading the installation instructions for each unit I discovered a unique requirement that Garmin lists:  The unit needs to be mounted 20-38" away from a compass (distance depends on the model).

I did some Internet surfing and found that people don't seem to pay much attention to this requirement.  People seem to mount the GPS on their pedestals all the time, and very few report any detectable issues.  However, I wonder how many people have really measured deviation at all compass points?  I tend to think the issue is minimal at best, however, knowing that Garmin says, "don't do it" puts a huge negative mark against the Garmin units.  Based on this, I'm leaning heavily towards the Standard Horizon CP180i.

Bebi Owl Aqua Signal Mounting

New Nav Lights

Introduction

I'm not sure about what is original and what was modified over Ravat's 34 years of life to date, but I am certain that I didn't like it.  The stern 180 degree light was a small incandescent Perko vertical mount unit which is still available through West Marine, although most other stores do not seem to advertise it.  The bow rail has an Aqua Signal Series 40 light mounted to a stainless bracket which was welded in place.  when I connected the wires after launching, neither light worked.

The first decision I had to wrestle with was whether or not to go with LED lighting.  From a pure design perspective, it's not much of a decision.  It's the best option in terms of reliability, long term cost, and energy efficiency.  And yet, I went with incandescent lighting.  I don't do a lot of sailing at night, in fact, I would usually sail until sunset, then get back to port within an hour, and then motor to my slip.  With that in mind, the energy reduction benefit of LEDs was significantly reduced due to my usage.

As this is one of (way, way, way) too many projects in flight right now, the budget could be reduced substantially by selecting a unit that offers a quality housing and a well known upgrade path to LED bulbs.  The Aqua Signal Series 25lights meet those criteria.  They are size-appropriate to my boat, offer mounting options that suit my needs, and are extremely reasonable in price.  Did I mention they are available just about everywhere as well?  Nice.

In my opinion the AS Series 40 is far to large for a pleasing proportion on the CS27's delicate bow.  I liked the slick welded mount, but really never liked the light there.  What really decided the fate of this upgrade was that no matter what I did, I could not get the bulb to stay on any better than intermittently.  That, one might think, could be a problem at night.  While there are many options, I decided to go with the Aqua Signal Series 25 lights because they are very inexpensive, and yet every bit as good quality as the old one that lasted over 30 years.  The smaller size makes a much more pleasing effect on the bow rail.

The Perko stern light seemed a bit too small to me, although that's not really a significant complaint, nor was it the reason I decided to ditch it.  When I opened up the fixture to see if 12V was appearing at the socket, I got a good close look at the lens.  It should be clear, but the center 50% has frosted to white.  This, no doubt, had a negative effect on the light's visibility at night.  On closer inspection, it appears that at some point in time the bulb, or something extremely hot, had melted into the plastic lens.  This doesn't seem like a good situation.  Further, the socket was in pretty bad shape.

Stern Light

The stern light required little more than drilling new holes in the stainless bracket which is welded to the rail.  However, to make the job "right" I needed to go one step farther.  The AS25 light is about an inch wider than the original Perko light.  This extra width protrudes beyond the stainless plate, and would be vulnerable to bumping.  Over time, a crack could develop, or the light could be knocked off.  This seems entirely avoidable to me.

To address this, I created a new bracket out of 1/4" marine lumber (StarBoard).  It could just as easily have been a piece of 1/4" FRP, but I didn't want to have to finish it.  This piece then mounted between the light and the bracket to provide a bit more support in the event of a bump.  The wiring enters through the lower corner screw hole rather than the center because the normal wire path is covered by the stainless bracket.

The installation is strong, and looks good as well.

Bow Light

No matter how I tried, I could not come up with a good way to mount the AS25 light to the AS40 bracket.  I ran through every combination of zip ties, duct tape, epoxy, drilling, and bolts that my imagination could muster.  Not gonna happen.  I'm much happier with the solution I ended up using though.

Aqua Signal makes a rail mount bracket which works wonderfully.  The only problem is that it costs nearly $60 to mount a $25 light.  I wasn't so happy about that, but it was the right thing to do, and by far more elegant than any alternative I could arrive at.  So, I bit the bullet and ordered the bracket.  The bracket was a bit of a puzzle to assemble as it came with no instructions.  I wouldn't quite call it intuitive, by process of elimination and some head scratching came through for me.  The only modification I had to make involved a Dremel tool to help the bracket accept the profile of the curved rail.  Minor grinding was all it needed.

Wiring

The final step was to hook it all back up.  I left the original wiring in place, although I didn't really want to.  It was not good tinned marine wire, but it was already fished through the rails, and I really didn't want to spend the next two days messing with it, or worse yet, remove the rails tat I had bedded only a few months ago.  So, I left a short pigtail inside the hull under each rail, and connected a new 16/2 tinned wire for the run back to the wiring panel.

I have a DC breaker which feeds a Blue Seas Dual-Bus which I use for my Nav Lighting devices.  Not only does it feed the bow and stern light, but it also provides power to back-light my compasses.  All connections were made using tinned heat shrink ring terminals which I obtained through GenuineDealz.com.  

Electronics Projects

This is the fun stuff.  The toys!  Electronics are the electrical components installed throughout the boat for various purposes.  Not to be confused with electrical items, which are the infrastructure of the boats electronics.  Batteries and wires are electrical items, but a stereo is considered electronics. 

Instrument Replacement

The original knot log reads 10 kts standing still, and 10 kts. when I'm at hull speed.  Is that ok?  I wasn't sure either, so I decided it was time to upgrade to a modern instrument system.

VHF Radio + Antenna

The old unit only picks up weather.  No transmit, no receive, no good.  I promised my wife that I was going to responsible when it comes to safety, and with very nice units costing less than $200, there's just no excuse.

GPS Navigation System / Chartplotter

I am currently using a hand-held unit for navigation.  It works just fine, but it slides off the seats and requires frequent battery changes.  It also is a very poor interface for plotting courses and reviewing or managing waypoints.  While not as critical as a VHF radio, I view this as being a pretty important piece of equipment, especially considering that it feeds the ability of a VHF radio to transmit current position to those who would come to aid.

Marine Stereo

In my dream I'm enjoying a little Jimmy Buffet while I gently rock on my anchor rode sipping a glass of wine watching the sunset.  I don't need to shake the keel, but a boat has to have tunes, and mine currently does not.

Bebi Owl Anchor Light Mounting
Purchasing the Bebi Owl was a no-brainer, but mounting it took a little more thought.  In this project I mounted the Owl anchor light inside an Aqua Signal Series 40 housing.

Mast Lighting Update

The mast on Ravat was fit with a combination deck light / steaming light.  Unfortunately, neither of those lights worked.  I also really wanted an anchor light hard wired into the boat, and I wanted it atop the mast.

DIY Custom Nav Pod (Instrument Housing)
A small plastic (OK, fiberglass) box to mount my chart plotter and auto pilot head will run me about $400.  Seriously?  I think I can afford to botch this project up about 20times and still come out ahead.  It's not that hard, but it is time consuming.  This worked out well to fill time gaps while waiting for other orders to come in.

New Running / Navigation Lights
Ravat had a strange mix of Aqua Signal and Perko lights, neither of which pleased me.  The housings were worn out and the fixture assemblies were corroded.  Time for something new.  This project installs Aqua Signal Series 25 lights on the CS27.

Yanmar YSB-8 Belt Replacement

Gates Green Stripe Belts come highly recommended from just about every source I can locate.  Since I couldn't find *any* negative comments about them I decided to go with the winds of wisdom.  Unfortunately, Gates doesn't make a belt small enough for the water pump, and the technician at the store was concerned that the green strip belts did not have as high a sidewall as my original.  That means it may not have the proper "bite" on the pulleys.

The next thing I did probably should have been the first.  I went to the CS Owners Association Yahoo Group and did some digging there.  Turns out that somewhere around page 4 of the search results I came on this:

> The Yanmar part numbers are 104214-42780 (water pump).  Not bad at $6.30!
> and 104211-42780 (alternator). Again, priced at $6.30.
> You can order from www.marinedieseldirect.com

Ahh ha!  Saved by CSOA yet again.  Seriously, if you have a CS Yacht and haven't joined this group you need to.

In the interim I picked up a new Gates XL 7290 alternator belt.  My new plan will be to order the correct Yanmar belts from the web site above if my local marina doesn't have them in stock.  I'm amazed that these Yanmar parts are reasonably priced.  I would have expected a hefty marine tax on them.  Certainly makes it an easy decision to have a few spares around.

CS27 Engine Projects

My CS27 came equipped with a Yanmar YSB8 diesel engine.  It works like a champ, it's incredibly simple, and I'm happy to have it.  This page summarizes all projects associated with the engine system.

Replace Cutlass Bearing and Realign Engine

The cutlass bearing was an incorrect size, and to make matters worse, the engine was very badly aligned.  This meant that even after installing a new cutlass bearing, if I didn't take care of the engine alignment it would be shredded just like the old one.  No option here but to throw more money at the vessel and hope for the best.

CS27 / Yanmar YSB8 Oil Change

Here's my process for changing the oil on my boat. (Coming soon...)

Yanmar YSB8 Belt Replacement

Very easy to do when you know what you need!

CS27 CAV296 Fuel Filter Replacement

These things are a bit old, but replacements are still available if you know how to find them.

Add Engine Raw Water Strainer

Ravat currently has a true raw water intake.  There's no strainer at all.  I'm not convinced this is good.

Engine Zinc Replacement

Engine zincs help to avoid corrosion.  This article describes where they are and how to change them.

Stuffing Box Adjustment / Packing

I had to pull the propellor shaft to replace the cutlass bearing, so this was a good excuse to proactively replace the packing in the stuffing box.

Transmission Oil Change

Did you even know there was a transmission back there?  Oh joy, another maintenance activity I didn't have a baseline for!

Hour Meter and Tachometer Installation

I think it's important to maintain good maintenance logs, and having an hour meter is an important foundation for those logs.  TinyTach seems to make a reasonably priced model that's not too hard to install.

Sound Deadening Panels

I'm anxious to reduce the sound coming out of the depths of my cockpit floor.  Cruising on this boat for any length of time with the motor running would not be pleasant.

Add Engine Room Temperature Monitor

Rumor has it that you don't want your engine room temperature over 130 degrees F.  A great tip I received from the CSOA list was to install an indoor/outdoor thermometer which transmits remotely to monitor those temps.  Might be important after installing the sound deadening!